fbpx

DIY Dog Leash Tutorial

Hearts and paws icon

Dog DIY By Jocelyn Okamoto 2 min read May 5, 2022 2 Comments

K9 of Mine is reader-supported, which means we may earn a small commission through products purchased using links on this page. Here’s how it works.
DIY DOG LEASH

DIY Dog Leash Tutorial

Learn how to make your very own dog leash for your pup!

  • Difficulty: Easy

Supplies Needed:

  • Cotton fabric
  • Bolt snap
  • Nylon webbing strap 

*The strap and hardware I used were 1 inch thick.

Directions:

If you haven’t seen it already, I also created a tutorial on how to create a dog collar. This is much simpler, so if you were able to follow along the collar tutorial the leash should be easy for you to make!

DIY DOG LEASH6

First, cut the nylon webbing strap to length. I cut mine about 53.5 inches long. Next, use a lighter to burn each end so the edges don’t fray.

DIY DOG COLLAR3

Next, cut your fabric about 3.75 inches wide and long enough to cover the length of the strap (approximately 54.5 to 55 inches).

DIY DOG COLLAR4

On one edge of the fabric, press a 1-inch fold.

DIY DOG COLLAR5

I sewed a basting stitch as a guide 2 inches from this pressed hem. Flip the fabric over and press along this basting stitch toward the other fold.  Remove this stitch after you iron. 

You can omit the basting stitch and just use the iron to press these guides if you prefer!

DIY DOG COLLAR6
DIY DOG COLLAR7

Next up, we’re going to sew the fabric onto the strap. 

First, tuck the nylon strap neatly under the 1-inch fold.

DIY DOG COLLAR8

Then, fold the other side of the fabric up so the entire strap is covered. If done correctly, the folded-over pressed edge will get close to the end of the strap without overlapping.

DIY DOG COLLAR9
DIY DOG COLLAR10

I used binder clips instead of pins to hold my strap together and sewed around the entire piece, making sure to fold over and tuck in the edges at the two ends. Essentially, I sewed a very thin and long rectangle using the presser foot as my guide to keep my seams close to the edge.

DIY DOG COLLAR11
DIY DOG COLLAR12

To finish your leash you’ll need to attach the bolt strap and create a handle.

DIY DOG LEASH1 1

On one end, pull the strap through the bolt snap about 2 inches. Next, sew the strap together to lock that bolt strap in place.  

Like in the collar DIY, everytime I sew the strap together I made sure to sew a rectangle with a cross through it a couple of times for added security. If you are worried about durability, use a heavy duty thread and feel free to sew more than one seam to hold these two pieces together.

Finally, on the other end of the strap, you can sew your handle. I folded my strap over about 8 inches and secured this in place with the rectangular stitch near the end of the strap.  

DIY DOG LEASH2 1
DIY DOG LEASH3 1

And you’re finished! This clips easily onto the D-ring of your dog’s collar. This is super easy to make and is a fun way to change up your dog’s accessories.

DIY DOG LEASH4 1
DIY DOG LEASH5 1

ADDITIONAL NOTES:

Sewing the fabric to the strap uses the same instructions as the collar, so the same photos will work! 

DIY DOG COLLARTHUMB3

Let us know how this project went for you in the comments!

homemade crockpot recipes for dogs
Recommended For You

Homemade Dog Food: The 7 Best Crockpot Recipes For Your Canine

Dog

Join our pup pack!

Get tons of great dog training advice and tips about gear!

Mailbox

2 Comments

Leave a Comment

Name
Email Address
Comment
Lisa

Hi! I love this simple tutorial. I was actually wondering where you found the hardware. I am worried that most of what I find would not be strong enough for a dog who pulls hard.

I love how you cover all of the nylon webbing with the fabric. It makes it look so neat and personalized! Thank you for sharing.

Reply
Ben Team

Hey there, Lisa.
I’m not sure exactly where Jocelyn found the one she used, but here are some similar connectors on Amazon.
🙂

Reply

Also Worth Your Time